Designed for hazardous environments, the Digitron P200L is suitable for use with non-corrosive, non-ionic liquids and gases. Liquid pressure can be measured using an air buffer.

The Digitron P200L measures from 0-199.9mbar on the low range to 0-500mbar on the high range. Connections are push fit 4mm/0.157" I.D. 6MM/0.236" O.D. nominal, retaining nut supplied.

Certified by BASEEFA, the UK's leading ATEX approvals house, the Digitron P200L is classified as EEx ia IIC T4. This certification is equivalent to EN 50 014:1997 + Amendments 1&2 and EN50 020:2002. The units are ready for site use anywhere, immediately.

Case proven the tough construction of the Digitron P200L makes them extremely durable and, therefore functional in not only hazardous atmospheres but also rough environments.
Manufacturer: Digitron
Part No : DIGP200L

Based on the Fluke 87V, the Fluke 87VEx has all the measurement and troubleshooting functions that the Fluke range offers.

Unlike most other ATEX-certified tools, the Fluke 87VEx can be used both inside and outside the hazardous zone (ATEX Zones 1 & 2, safety rating II 2G EEx ia IIC T4) without compromising performance or compliance, so there's no need to carry different tools for use in different areas. The Fluke 87VEx also has a built-in thermometer with TC probe, further reducing the need to purchase extra ATEX tools, which can be costly.

The key features of the Fluke 87VEx are:

• True-RMS voltage and current for accurate measurements on non linear signals
• 20kHz Bandwidth
• Selectable filter for accurate voltage and frequency measurements on motor drives
• Large backlit LCD display with analogue bargraph
• Auto & manual ranging for maximum flexibility
• Min-Max-Average

An ATEX approved loop calibrator for use in explosion endangered areas. The Fluke 707Ex is certified in accordance with the ATEX directive (Ex II 2 G Eex ia IIC T4) in Zones 1 and 2.

The Fluke 707Ex is a high performance solution for calibration, repair and maintenance of current loops. The new "Quick Click" knob makes it extremely fast and easy to use.

Features of the Fluke 707Ex include:

• One handed user interface with "Quick Click" detented knob, mA sourcing
• Simulation and measurement, 0.025% accuracy and 0.001mA resolution
• Simultaneous mA and % of span display
• Selectable step or ramp outputs
• 24 V Loop supply with mA measure including 250Ω HART resistor & 0-28 VDC measurement to check Loop Voltage

Supplied with red holster, TL75 test leads, alligator clips, battery and intruction sheet.
Manufacturer: Fluke
Part No : FLU707EX

The Seaward Type C is designed to measure voltage from 80 - 650V AC / DC. Previously classed as "Intrinsically Safe" for use in hazardous areas, it should be noted that this item DOES NOT meet the current ATEX standard. Please Click Here to read the compliance statement from Seaward.

The Seaward Type C conforms to BS1259 for Intrinsically safe circuits and to the UK Electricity Council Engineering Recommendation G9.

The Seaward Type C is a neon voltage indicator, enclosed within shock resistant enclosure, and is unaffected by immersion in water.
Manufacturer: Seaward
Part No : SEAC

HMS Dauntless stays on TRaC

HMS Dauntless, the second of the Royal Navy's class of air defence destroyer arrived at Portsmouth Naval base for the first time in December. Dauntless is one of six new Type 45 destroyers which will provide the backbone of the UK's naval air defences for the next three decades.

The impressive Sampson Radar from BAE Systems Integrated System Technologies is a striking feature, and was a particularly interesting project for TRaC in supporting BAE Systems Integrated System Technologies with qualification through means of vibration testing, finite element analysis and modal testing.

 

Image courtesy of BAE Systems Integrated System Technologies

 

Owing to the size of the unit under test (7m and 6 tonnes), the process for qualification went beyond conventional testing, and TRaC Employed a number of physical

TRaC Reaches Milestone in Worldwide Approval

TRaC, your partner for worldwide market access, has reached a major milestone, by now providing a turn-key test approvals management service for accessing over 150 countries.

The process of gaining test approvals for worldwide markets is complex; every region requires its own unique demonstration of compliance, making a 'one certificate fits all' approach impossible. Just as the CE mark applies to all goods traded in any European Member State, including those produced outside the zone, other worldwide markets impose their own compliance requirements. In developed countries such as the Americas, the requirements may be familiar to OEMs successfully trading in the European market. For developing regions, such as the CIS (Commonwealth of Independent States) or the Africas, the process is much more complicated.

Gaining access to the developing regions of the world is viewed by many as essential for growth. As traditional markets become saturated,

New automotive EMC test equipment

TRaC has purchased new automotive transient test equipment. TRaC customers can now benefit from testing automotive Electronic Sub-Assemblies (ESAs), with a continuous high current rating to the latest automotive transient specification ISO7637-2:2004, complementing the existing equipment.

Vehicles are in a very different environment from a house or office where large voltage transients are caused from the vehicle during a typical journey. These transients include cranking the engine, switching of large inductive loads (e.g. air conditioning), cables being disconnected inadvertently and other forms voltage spike.

ISO7637-2:2004 forms the basis of almost all the specific manufacturer specifications as well as the automotive directive 2004/104/EC (used for e-marking) and also products that are used in this environment to the EMC Directive (2004/108/EC).  The new NSG5000 system enables all the core pulse parameters to be adjusted to meet an individual manufacturer specification

Stress Analysis and Physical Testing - Complementary Processes or Alternatives?

A Presentation to the Engineering Integrity Society. TRaC, leading providers of environmental testing and finite element analysis (FEA) is delighted to be part of the Engineering Integrity Society (EIS) upcoming "Instrumentation, Analysis & Testing Exhibition" at Silverstone Race Track on 23rd February 2010.

The exhibition provides visitors with an opportunity to see and evaluate the latest industry developments within the Instrumentation, Analysis and Testing environment.

Dr. Peter Moir, TRaC's Technical Director, will deliver a paper on "Stress Analysis and Physical Testing - Complementary Processes or Alternatives". Finite Element Analysis is a commonly used means for de-risking the reliability and robustness of a design against its mechanical performance specification, particularly given the demands of faster times to market, cost reduction, etc.  Despite its widespread use, belief in computer simulation is still seen as a leap of faith by many technical and non technical decision

TRaC assists CSR in gaining Worldwide Approval of BlueSlim PC Host Bluetooth® Module Project

TRaC, internationally recognised as a test, certification and approvals expert, has received customer praise for its role in assisting CSR plc gain worldwide approval for one of the world's smallest PC Bluetooth® modules. The module is called BlueSlim.

Unlike many other test facilities, TRaC's extensive accreditations mean it is able to provide all of the testing and certification for all countries of sale, worldwide, in a single process. Not only does this drastically simplify the approvals process, but it also cuts the time and cost to launch new products into a global marketplace.  

Miguel Bravo-Escos, CSR's Technical Programme Manager said: "CSR appreciates TRaC's excellent work on this project and for getting our Bluetooth module qualified quickly and efficiently."

Through its worldwide accreditation and integrated project management services, TRaC is able to provide a single site solution for product approval,

11 ZigBee^® Home Automation products certified to meet growing needs of Home Automation market

28 Products Now Certified for Smart Home Use to Support Expanding Market. The ZigBee^® Alliance, a global ecosystem of companies creating wireless solutions for use in energy management, commercial and consumer applications, today announced the certification of 11 devices from five different companies using ZigBee Home Automation. There are now 28 products certified to help consumers and professional installers create smart homes that control home appliances, lighting, heating and cooling, energy use and security.

According to ABI Research, home automation system shipments will approach 2.8 million in 2011 as standards-based mainstream home automation systems and home automation as a service expand rapidly in 2010. New standards-based wireless technologies such as ZigBee mean that many mainstream home automation installations are decreasing in price, while the segment is further driven by the growing availability of peripheral components, according